首页 / 资料库 / 电路图
红外线开关电路-Infra Red Switch
2023-09-18 19:40:00
红外线开关电路-Infra Red Switch
This is a single channel (on / off) universal switch that may be used with any Infra Red remote control that uses wavelengths between 850-950nm.
Notes:
Any "button" of any remote control may be used to work this universal switch. The button must be pressed for two seconds (determined by R3 and C2) before the relay will operate. Once operated the circuit will remain in this state (latched) unTIl reset. To reset, any button is pressed and held for the delay.
For example, if you were watching TV, and your set was tuned to Channel 3, you could press and hold the TV remote controls channel 3 button for two seconds. That way the TV viewing would not be affected and the relay would acTIvate. You can connect anything to the relay, for example a lamp, but make sure that the relay contacts can handle the rated voltage and current.
Circuit OperaTIon:
IC1 is an Infra Red module. IR modulated pulses are received and buffered by this IC. It has a standard TTL output, the output with no signal is logic 1. One gate of a CMOS inverter and drives Red LED1 as a visible switching aid. Another gate buffers the signal and applies it to the TIme constant circuit, comprising R3,C2,R4 and D1. C2 charges via R3, and discharges via R4, D1 prevents quick discharge via the low output impedance of the CMOS buffer.
The pulses are further buffered and contain "jaggered edges" as shown above. These edges are produced by the modulated IR data, which has to be removed. This is achieved using IC3, a 555 timer wired as a monostable, pulse duration R5, C4. These cleanly reconstructs a single clean pulse to activate the bistable latch. A D type flip flop, IC4 is configured as a bistable. The input is applied to the clock pin, the inverted output fed back to the data input and clear and preset lines are tied to ground. For every pulse the relay will operate and latch, the next pulse will turn off the relay and so on. Note that quick turn on and off of the relay is not possible. The output pulse is set at about 1.5 seconds and input delay by R3, C2 set at two seconds.
Parts List:
R1 3k3
R2 1k
R3 22k
R4 220k
R5 1M
R6 3k3
B1 12 V
D1 1N4148
D2 1N4003
Q1 B109
LED1 CQX35A
IC1 IR1 available from Harrison Electronics
IC2 4049
IC3 CA555
IC4 SN74HCT74
IC5 LM7805
Relay 12 Volt coil with changeover contact
C1 100u
C2 22u
C3 100n
C4 2u2
最新内容
手机 |
相关内容
比较器芯片和运放电路的区别
比较器芯片和运放电路的区别,运放,芯片,比较器,信号处理,响应,需求,比较器芯片和运放电路是常用的电子元件,它们在电路设计和信号处支撑高端芯片研发,合见工软进军国产
支撑高端芯片研发,合见工软进军国产EDA全流程,软进,研发,芯片,布局,中国,垄断,合见工软(HuaJian Microelectronics)是一家专注于EDA(Ele基于单片金纳米线逻辑电路的多功能
基于单片金纳米线逻辑电路的多功能智能可穿戴设备开发,智能,可穿戴设备,逻辑电路,健康,分享,监测,随着科技的不断发展,可穿戴设备已电阻、电感与电容的区别
电阻、电感与电容的区别,常见,介电常数,电路设计,性是,单位,温度,电阻、电感和电容是电路中常见的三种基本元件,它们在电路中起着不如何设计一个对按键信号进行计数的
如何设计一个对按键信号进行计数的计数器?,计数器,信号,全加器,触发器,输出,输入,设计一个对按键信号进行计数的计数器可以通过使用铌酸锂的应用-射频滤波器
铌酸锂的应用-射频滤波器,滤波器,通道,频率,损耗,性能,封装,铌酸锂(LiNbO3)是一种重要的晶体材料,具有优异的光学、电学和声学性能,广泛全数字波束形成芯片的特性和应用场
全数字波束形成芯片的特性和应用场景,应用场景,芯片,数字,数字信号处理,调整,灵活性,全数字波束形成芯片是一种集成电路芯片,用于实数字电路中的计数器详解
数字电路中的计数器详解,计数器,数字电路,十进制数,触发器,用于,十进制,数字电路中的LM2575S-ADJ计数器是一种重要的组合逻辑电路,用