首页 / 百科
MAX7060 280MHz to 450MHz Progr
2010-02-28 00:00:00
MAX7060 280MHz to 450MHz Programmable ASK/FSK Transmitter 概述The MAX7060 frequency and power-programmable ASK/FSK transmitter operates at 280MHz to 450MHz frequencies. This device incorporates a fully integrated fractional-N synthesizer, which allows the user to set the RF operating frequency to a large fraction of the 280MHz to 450MHz frequency range with a single crystal. For example, the MAX7060 can be tuned from 285MHz to 420MHz with a 15MHz crystal. The RF output power is user-controlled between +14dBm and -14dBm, with a 5V supply or with battery voltages as low as 3.2V. At the minimum specified battery voltage of 2.1V, the RF output power-control range is between +10dBm and -14dBm. To maintain a good output power match across a broad range of frequencies, the MAX7060 also contains a programmable matching capacitor connected in parallel with the power amplifier (PA) output.
ASK modulation is accomplished by switching the PA on and off, so excellent modulation (on/off) ratios are achieved. ASK amplitude shaping is available to reduce the width of the transmission spectrum. FSK modulation is accomplished by changing the coefficients of the high-resolution fractional-N synthesizer, so FSK deviation is extremely accurate. Data rates up to 50kbps Manchester coded for ASK and 70kbps Manchester coded for FSK can be maintained while still satisfying regulatory emission-bandwidth standards. The full set of configuration functions are handled by an on-chip serial peripheral interface (SPI™). There is also a manual mode where a limited number of settings can be made directly through selected pins.
The startup time is very short, and data can be transmitted 250µs after the enable command. The MAX7060 operates from a 2.1V to 3.6V supply, or internal regulators can be used for supply voltages between 4.5V and 5.5V. The standby current in the 3V mode is 400nA at room temperature, and can be reduced to 5nA using the low-power shutdown (LSHDN) pin.
The MAX7060 is available in a 24-pin (4mm x 4mm) thin QFN package and is specified for the automotive temperature range from -40°C to +125°C. 关键特性Fully Integrated, Fast Fractional-N PLL Programmable Power Amplifier Tunable PA Matching Capacitor Control Through SPI or Manual Settings Low Shutdown Current for 2.1V to 3.6V Supply Supply Flexibility 24-Pin (4mm x 4mm) TQFN Package FCC Part 15, ETSI EN 300 220 Compliant*
ASK modulation is accomplished by switching the PA on and off, so excellent modulation (on/off) ratios are achieved. ASK amplitude shaping is available to reduce the width of the transmission spectrum. FSK modulation is accomplished by changing the coefficients of the high-resolution fractional-N synthesizer, so FSK deviation is extremely accurate. Data rates up to 50kbps Manchester coded for ASK and 70kbps Manchester coded for FSK can be maintained while still satisfying regulatory emission-bandwidth standards. The full set of configuration functions are handled by an on-chip serial peripheral interface (SPI™). There is also a manual mode where a limited number of settings can be made directly through selected pins.
The startup time is very short, and data can be transmitted 250µs after the enable command. The MAX7060 operates from a 2.1V to 3.6V supply, or internal regulators can be used for supply voltages between 4.5V and 5.5V. The standby current in the 3V mode is 400nA at room temperature, and can be reduced to 5nA using the low-power shutdown (LSHDN) pin.
The MAX7060 is available in a 24-pin (4mm x 4mm) thin QFN package and is specified for the automotive temperature range from -40°C to +125°C. 关键特性
- 280MHz to 450MHz RF Frequency
- Frequency Range 100% Tested at +125°C
- < 250µs Startup Time
- Adjustable FSK Mark and Space Frequencies
- Ultra-Clean FSK Modulation
- 50kbps Manchester Data Rate ASK
- 70kbps Manchester Data Rate FSK
- +14dBm Tx Power with 5V Supply
- +10dBm Tx Power at 2.1V Supply
- 28dB Power-Control Range in 1dB Steps
- 400nA Standby Current, Power-On-Reset (POR) Active
- 5nA Shutdown Current, POR Inactive
- 2.1V to 3.6V Single-Supply Operation or
- 4.5V to 5.5V Supply Operation with Internal Regulators
应用/使用
Garage-Door Openers
Home and Industrial Automation
远端控制
安全系统
传感器网络
Pin Configuration/Functional Diagram
最新内容
手机 |
相关内容
采用89C2051制作的120MHz频率计
采用89C2051制作的120MHz频率计,电路图,消费类电子电路图,采用89C2051制作的120MHz频率计 采用,89c51,制,采用89c51制作的120MHz频1Mhz发光二极管脉冲调制电路
1Mhz发光二极管脉冲调制电路,电路图,光电产生电路,1Mhz发光二极管脉冲调制电路 1Mhz,发光二极管,1Mhz发光二极管脉冲调制电路1.5 5.7MHZ光学隔离式VFO电路图
1.5 5.7MHZ光学隔离式VFO电路图,电路图,光电隔离电子电路图,1.5 5.7MHZ光学隔离式VFO电路图 ,光学隔离,VFO,1.5 5.7MHZ光学隔离式VF1.5 5.7MHZ光学隔离式VFO电路图
1.5 5.7MHZ光学隔离式VFO电路图,电路图,光电隔离电子电路图,1.5 5.7MHZ光学隔离式VFO电路图 VFO,1.5 5.7MHZ光学隔离式VFO电路图50MHZ光电检波电路图
50MHZ光电检波电路图,电路图,光电探头电路,50MHZ光电检波电路图 检波,50MHZ光电检波电路图900mhz射频指示器电路图
900mhz射频指示器电路图,电路图,光电报警电子电路图,900mhz射频指示器电路图 指示器,900mhz射频指示器电路图 该电路的灵敏利用CMOS对管做成的2MHZ晶体振荡器
利用CMOS对管做成的2MHZ晶体振荡器电路,电路图,数字时钟电路图,利用CMOS对管做成的2MHZ晶体振荡器电路 晶体振荡器,利用CMOS对管做2MHZ主时钟电路图
2MHZ主时钟电路图,电路图,游戏电路,2MHZ主时钟电路图 2MHZ,主时钟,2MHZ主时钟电路图